Home > News > Content
Cartridges Can Be Divided Into One By One Structure And Split
Oct 17, 2017

Cartridges can be classified according to color or structure: according to the color can be divided into monochrome, three-color, colored, etc .; according to the structure can be divided into one and split. In order to achieve better printing results while simplifying the maintenance process, one cartridge will be integrated into the cartridge, ink cartridges and nozzles at the same time installed on the trailer, the printer becomes the most critical components. This one-piece ink cartridge structure is simple, the volume can be done very small, G2 Cartridge and the cost is low, to change ink for the nozzle, the higher cost of supplies. The other is split, the ink cartridge and the nozzle separately, ink only after the use of ink cartridges, so the cost of supplies is low. G2 Cartridge But because of the separation between the ink cartridge and the ink jet head, can not be sealed after installation, it may be due to dust and poor installation and other reasons caused by inkjet failure

The internal structure of the ink cartridges is not complicated, mainly by the ink sponge and pressure jet auxiliary device. Whether it is a one-piece cartridge or a split cartridge, the jetting aid requires a filter, a sealing film and a sealing ring, which helps the ink to reduce the particle size during the splashing process while ensuring accurate pressure balance.

The choice of the jetting aid is also related to the working mode of the ink cartridge. At present, G2 Cartridge it is mainly divided into bubble type and microneedle type piezoelectric type. From the printing effect point of view, the bubble technology can be improved after a very good effect, not lost in the micro-pin point of piezoelectric inkjet technology.

In addition to inkjet inkjet technology, the type of ink will have no small impact on the print quality. If the color classification, ink can be divided into dye-based ink and pigment-based ink. G2 Cartridge Dye-type ink is a dye-based ink, is currently the ink used in most inkjet printers. Pigment-based ink is pigment-based ink, a better color fullness, more suitable for photo printing. If the difference between the ink solvent can be divided into water-based ink and oil-based ink. The water-based ink is mainly composed of water and a water-soluble solvent as a dissolving color base, and the oil-based ink is a non-water-soluble solvent as a main component of the dissolved color base.

Use ink cartridges correctly

(1) Install the ink cartridge

Cartridge installation process is not complicated, we can follow the steps on the instructions. The only thing to remind you is that the cartridge must be inserted into the cart before the cartridges must be removed before the seal on the vent hole, otherwise the printer can not complete the filling action, G2 Cartridge although the print action, but the print out are white paper.

After the cartridge is installed, it needs to be calibrated because the physical location of the cartridge must be sufficiently accurate, otherwise it will reduce the print. For ordinary home users, the printer in the normal use of six months after the need to correct the cartridge in time to ensure the normal print quality of the printer. Cartridge correction operations generally need to pass the printer with the program, G2 Cartridge print the test page, and then adjust the output according to the situation.

(2) Can not be used after replacing a new cartridge

Under normal circumstances, when the ink has been used up, the printer will prompt "ink exhausted." If you replace the new cartridge, the printer prompts "ink exhausted", one may not be installed ink cartridges, the other may be in the off state to take their own old ink cartridges, replace the new cartridge. Because the ink cartridge is reused after the cartridge is replaced again, the printer will not be able to detect the ink cartridge in the shutdown state, so that the printer can not detect the ink cartridge on the reinstallation. In addition, G2 Cartridge some printers measure the ink capacity is to use the internal electronic counter to carry out the printer, when the counter reaches a certain value, the printer to determine the ink exhausted. In the ink cartridge replacement process, the printer will reset the internal electronic counter to confirm the installation of a new cartridge. G2 Cartridge The solution is very simple, just turn on the power, move the trailer to the cartridge replacement position, and then install the cartridge and then let the printer charge, filling the end of the process can be troubleshooting.

Tip: cartridges can not put casually

The operating characteristics of the home printer can be summarized in terms of intermittence, because the home and SOHO user printers are used for a while, depending on the commercial or office printer, and there is a problem with how the open cartridges are kept. When unpacking the new cartridges, carefully lift the plastic cover and keep the cartridges out of the package. Wait until the ink cartridge is temporarily not used, G2 Cartridge put it back into the plastic box, will have opened the plastic tube cover with double-sided tape and the box tightly bonded to ensure that the ink and the outside world. Of course, you can also use a variety of other suitable containers to store the cartridge, as long as the attention of the container lid joints with plastic tape sealed.