Home > News > Content
Introduction To Ink Cartridges
Jun 20, 2017

The ink cartridge mainly refers to the parts used in the inkjet printer (including the inkjet all-in-one) to store the printing ink and finally finish printing.

classification

Cartridge from the current composition of the structure on the point of view, in general, G2 Cartridge can be divided into: split cartridges and one cartridge.

One-piece ink cartridge

One type of ink cartridge is to integrate the nozzle on the cartridge, when the ink runs out after replacing a new cartridge, it means that at the same time replaced a new print head. The use of this cartridge can achieve a relatively high printing accuracy, and can guarantee the print quality, G2 Cartridge because the nozzle with the replacement of the cartridge, so the inkjet head will not wear and reduce the print quality. But this ink cartridge design structure increases the cost, and the price of such cartridges are relatively high. HP, Lexmark products using such cartridges. However, in order to save the cost of printing, for these cartridges, users in the cartridge after the use of their own often empty ink tank to re-irrigation of ink, in general, as long as the operation is correct, after filling the ink will not cause much damage to the nozzle. Even if there is no success, the scrapped is only a should be scrapped by the original ink only, the general will not cause damage to the printer. Of course, G2 Cartridge this type of ink cartridges can not limit the number of users to fill the ink, in general, after using the original ink, you can also fill 3 to 4 times. If you find a significant decline in print quality, then the need to replace a new cartridge.

Split ink cartridges

Split ink cartridges are products that separate the nozzle and cartridge design. The starting point of this structural design is mainly to reduce the cost of printing, because this cartridge is not integrated in the print head, the cartridge is invalid when the print nozzle can continue to use, G2 Cartridge but also simplifies the user's cartridge assembly process, The printer has the opportunity to damage; but the cartridge structure is also a significant flaw, that is, the nozzle will not be updated in time, the printer with the working hours of growth, the quality of the printer naturally dropped until the nozzle so far. Epson's products are mostly split-type ink cartridges. This kind of ink cartridges from the cost, it is lower than the integrated ink cartridges, G2 Cartridge but this type of ink cartridges do not allow users to fill the ink casually. In the split-type ink cartridges, according to the color of the situation can be divided into monochrome ink cartridges and multi-color ink cartridges. Monochrome ink cartridges refer to each color is individually packaged, which color can be used for which one can not cause waste. And multi-color ink cartridge is a variety of colors will be packaged in a cartridge, if a color runs out, even if several other colors have, you must also replace the entire cartridge. Obviously, monochrome ink cartridges to be more economical.

Ink cartridges for the entire inkjet printer has a very important position, especially some low-end printers, has reached 2 boxes = 1 printer price. Therefore, G2 Cartridge in the purchase of the printer, you must consider the situation of the cartridge.

How do I clean my own cartridges?

1, carefully remove the ink cartridge from the printer.

2, remove the cartridge, find the cartridge of the nozzle (the bottom of the cartridge similar to the part of the integrated circuit).

3, prepare a pot of warm water (50 ~ 60 degrees Celsius), the bottom of the cartridge nozzle into the water soak for 5 minutes, be careful not to put the entire cartridge into the water.

4, the cartridge removed from the water, G2 Cartridge the appropriate forced rejection rejection, until the nozzle part of the ink flow out, with a thin cotton or napkin gently wipe clean. Be careful not to wipe the nozzle directly, otherwise it will easily cause the nozzle to block, resulting in poor print text.

5, the toilet after the appropriate ventilation to dry, and then re-installed into the printer.

At this point if the print effect is still bad, we must consider replacing the cartridge.